The single girder travelling crane is our flexible crane for almost any application. Even in buildings with low ceilings effective material flow solutions can be achieved for loads of up to 16 t and spans of up to 39 m.
Normally safety clearances below ceilings are not required for single girder cranes within this load range. This allows the optimal use of existing space or can save additional building height costs.
The single girder traveling cranes adapt to different building applications due to their various main girder connection variants. Favorable crane dimensions help to reach optimal highest hook positions.
Contents
The main girder connection ‘version 3’ is the optimal solution for new factory buildings as this version offers the best side approach dimensions. If lifting height is the decisive factor then a single girder crane ELS with a side-running trolley is the right choice.
The single-girder traveling crane is also a good choice for special solutions: The accessories and components offer specialized additional equipment to satisfy your requirements.
Robust rolled section girders form the crane girder of the single girder traveling crane ELV whereas, traveling cranes ELK and ELS consist of torsion-resistant welded box girders.
Single Girder vs. Double Girder Design
A single girder or double girder design will be one of the largest contributors to the complexity and overall cost of a new overhead crane system.
A bridge crane is a type of overhead crane that includes two or more overhead runways built into the building’s support structure. Bridge cranes have different configurations and can be comprised of one or two beams—more often referred to as a single girder or double girder design. Girders can be made of rolled steel or can be fabricated by welding the beams into a steel box design for added strength and rigidity.
The bridge is a load-bearing beam that runs the width of the crane bay and is the primary structural component that connects the runways and moves the hoist forward and backward using a trolley.
The trolley and hoist can be designed to be top running or under running depending on the design of the building structure and the requirements needed to make the lift.
A single girder or double girder design will be one of the largest contributors to the complexity and overall cost of a new overhead crane system. In this article, we’ll discuss the advantages, disadvantages, and differences between single girder and double girder bridge crane systems.
You’ll want to give careful consideration to the bridge design of your overhead crane system to make sure that you understand the requirements of the lifting task and the environment where the crane will be operating.
On a single girder crane, the bridge consists of one girder beam supported on each side by an end truck. The trolley and hoist are most commonly underhung—meaning they run on the bottom flange of the bridge. The bridge itself can either be top running or under running in design.
One of the most common misconceptions about single girder cranes is that they are not as durable or of the same high quality as double girder cranes. If properly designed, a single girder crane can be the perfect solution for a business that needs a light to medium duty crane, or for a facility where headroom and/or floor space is limited.
The major disadvantage of a single girder crane system is that they do have a limit in terms of capacity, span, and hook height. A double girder crane may be the better solution for overhead cranes that require capacities over 15 tons and spans over 65 feet.
In addition, service walkways, enclosed or exposed operator cabs, magnet cable reels, or other specialized features can be difficult or expensive to incorporate into the crane’s design.
Advantages of a Single Girder Design:
Disadvantages of a Single Girder Design:
On a double girder crane, there are two girder beams that make up the bridge and they’re supported by an end truck on each side. In most instances, the trolley and hoist run on a rail installed on top of the bridge girders. With a double girder design, you gain the depth of the cross girder if the hoist is placed between or on top of the cross girders—providing an extra 18”-36” of hook height in most cases.
Double girder cranes can be either top running or under running in design. A top running double girder bridge crane will provide the most overhead room, as well as the greatest hook height.
Double girder cranes are recommended for heavy-duty applications where the crane has to handle heavier capacities and longer spans. Because of this, the components of the crane system, including the hoist and trolley, are more complex in design—making double girder cranes more expensive than a single girder crane.
They also require more material for the bridge beams and the runway system, so extra consideration should be given to the building’s support structure. Additional tie-backs or support columns may need to be added to handle the additional deadweight on the supports or building foundation.
Double girder bridge cranes are ideal for lifting heavy loads and can be used in more frequent operation than a single girder crane. They can also be used both indoors and outdoors, in a bridge or gantry set up, and are frequently used in mining, iron and steel production, railyards, and shipping ports.
Advantages of a Double Girder Design:
Disadvantages of a Double Girder Design:
The main traveling structure of the crane which spans the width of the bay. The bridge consists of two end trucks and one or two bridge girders depending on the equipment type.
Located on either side of the span, the end trucks house the wheels on which the entire crane travels. These wheels ride on the runway beam allowing access to the entire length of the bay.
The principal horizontal beam of the crane bridge which supports the trolley and is supported by the end trucks.
The unit consisting of both the hoist and the trolley frame. In situations where more than one hoist is required on one crane, both hoists can be supplied on a single trolley or on separate trolleys.
The trolley carries the hoist across the bay along the bridge girder(s) traversing the span.
The hoist is mounted to the trolley and performs the actual lifting function via a hook or lifting attachment. There are two basic types of hoist. The Munck brand is a Wire Rope Hoist which is very durable and will provide long term, reliable usage. The other type of hoist is Chain Hoist.
When you purchase an overhead crane, you also benefit from our complete project management experience. This not only covers design and manufacture, but also delivery, installation, load testing, and final commissioning.
A gantry crane is slightly different from a bridge crane. The general premise is the same, but the operation is different. Some gantry cranes ride along a track installed on the floor or use a V-groove caster to keep moving in a straight line. Gantry cranes are usually less expensive than an overhead bridge crane.
The average pay for an Overhead Crane Operator is $59,000 a year and $28 an hour in the United States. The average salary range for an Overhead Crane Operator is between $42,500 and $72,250.
The Bureau of Labor Statistics reports that the average annual income of crane and tower crane operators was $50,000 on May 2012. This annual income figure is based on an average wage of $24.00 an hour and 2,050 hours of work per year.
While workers face many dangers on construction sites, crane operators are often at risk for catastrophic injuries. While crane accidents aren’t always caused by negligence, more often than not, they are preventable.
Arabic 
English 
Spanish 
Japanese 
French 
Indonesian 
Thai 
Russian 
Vietnamese